Ibase SI-18 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Počítače Ibase SI-18. IBASE SI-18 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - User Manual

SI-18 Series User Manual

Strany 2

10 Specification System Mainboard EB-900 Construction SGCC 1.0t Chassis Color Black / White Storage 2.5” 80GB SATA HDD x 1 Mounting Wall mount Dimen

Strany 3

11 Mounting SI-18 to the Wall You can install SI-18 on plastic (LCD monitor), wood, drywall surface over studs, or a solid concrete or metal plane

Strany 4 - Table of Contents

12 Mounting to hollow walls  Method 1: Wood surface – A minimum wood thickness – 38mm (1.5in.) by 25.4 cm (10in.) – of high, construction – grade

Strany 5 - Safety Information

13 SI-18 mounting bracket solution SI-18 mounting bracket (IBASE) part number: SC2SIMK1---0A1100P Please install SI-18 to the mounting bracket usin

Strany 6 - Care during use

14 Exploded view of the SI-18 assembly Parts description Part No. Description Part No. Description 1 HDD 2 HDD bracket 3 EB900 4 FAN Set 5 Fan br

Strany 7 - Acknowledgments

15 Installation Installing WLAN antenna (Optional) SI-18 has reserved one SMA connector hole for WLAN (wireless LAN) antenna connection on the I/O s

Strany 8 - Accessories

16 4. Use a screw driver to pinch out the knock-out metal-plate of the SMA antenna hole from point B. To avoid any metal falling into the system, p

Strany 9 - Components

17 6. Install the antenna washer, then the hex nut on the SMA connector and use a hex socket driver or pliers to fix the nut and secure the SMA con

Strany 10 - Specification

18 8. Wire the IPX connector on WLAN card and arrange the internal antenna cable routing. 9. Screw the bottom chassis back to the system with 8 s

Strany 11 - Mounting SI-18 to the Wall

19 Installing the memory The mainboard supports two DDR3 memory socket for a maximum total memory of 4GB in DDR3 memory type. Installing and Remo

Strany 12 - Selecting the location

Revision Release Date V0.1 2011/11/15 V0.2 2014/09/23

Strany 13

20 Setting Jumper Jumpers are used on the motherboard to select various settings and features according to your needs and applications. Contact your

Strany 14 - Parts description

21 JP2: LCD Panel Power Selection JP2 LCD Panel Power 3.3V 5V JP6: COM1 RS232 +5V/+12V Power Setting JP6 Setting Function Pin 1-2 Short/Close

Strany 15 - Installation

22 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. BIOS Introduction The BIOS (B

Strany 16

23 Main BIOS Setup This setup allows you to record some basic hardware configurations in your computer system and set the system clock. Note: If th

Strany 17

24 Advanced Settings This section allows you to configure and improve your system and allows you to set up some system features according to your pr

Strany 18

25 PCI Subsystem Settings This section allows you to configure the PCI, PCI-X and PCI Express settings. PCIE Configuration The fields under PCIE C

Strany 19 - Installing the memory

26 System BIOS Cacheable The setting of Enabled allows caching of the system BIOS ROM at F000h-FFFFFh, resulting in better system performance. Ho

Strany 20 - Setting Jumper

27 ACPI Settings This section configures the system ACPI parameters. Enabled ACPI Auto Configuration Enables or Disables BIOS ACPI Auto Configurati

Strany 21 - Pin Definition

28 CPU Configuration This section shows the CPU configuration parameters. Limit CPUID Maximum Disabled for Windows XP. PSS Support Enabled /disable

Strany 22 - BIOS Setup

29 Auto Power On Schedule This section setups the power on time for the system. Schedule Slot 1 Setup the hou/minute for sytem power on. Schedu

Strany 23 - Main BIOS Setup

3 Copyright © 2011 IBASE Technology INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be r

Strany 24 - Advanced Settings

30 USB Configuration Legacy USB Support Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. DISABL

Strany 25 - PCI Subsystem Settings

31 Super IO Configuration Serial Port 0/1 Configuration Set Parameters of Serial Port 0/1 (COMA/COMB) Power Failure The options: Keep last state, B

Strany 26

32 Chipset Settings This section allows you to configure and improve your system and allows you to set up some system features according to your pre

Strany 27 - ACPI Settings

33 North Bridge This section allows you to configure the North Bridge Chipset. IOMMU Mode IOMMU is supported on LINUX based systems to convert 32bi

Strany 28 - CPU Configuration

34 GFX Configuration PSPP Policy PCIe speed power policy. Memory Configuration Integrated Graphics Enable Integrate Graphics controller. Node 0

Strany 29 - IDE Configuration

35 North Bridge LVDS Config Select South Bridge This section allows you to configure the South Bridge Chipset.

Strany 30 - USB Configuration

36 SB SATA Configuration OnChip SATA Type Native IDE / n RAID / n AHCI / n AHCI / n Legacy IDE / n IDE->AHCI / n HyperFlash

Strany 31 - H/W Monitor

37 SB USB Configuration SB GPP Port Configuration

Strany 32 - Chipset Settings

38 SB HD Azalia Configuration Boot Settings This section allows you to configure the boot settings according to your preference. Setup Prompt Tim

Strany 33 - North Bridge

39 Quiet Boot Enables/Disables Quiet Boot option. GateA20 Active UPON REQUEST – GA20 can be disabled using BIOS services. ALWAYS – do not allow disa

Strany 34 - Memory Configuration

4 Table of Contents Acknowledgments ... 7 Accessorie

Strany 35 - South Bridge

40 Save & Exit Settings Save Changes and Exit Exit system setup after saving the changes. Disacard Changes and Exit Exit system setup witho

Strany 36 - SB SATA Configuration

41 Restore Defaults Restore/Load Defaults values for all the setup options. Save as User Defaults Save the changes done so far as User Defaults. R

Strany 37 - SB GPP Port Configuration

42 Driver Installation This section describes the installation procedures for software and drivers. The software and drivers are included with the m

Strany 38 - Boot Settings

43 AMD A55E Chipset Family Graphic Driver Installation Follow the steps below to install the AMD A55E chipset family graphics drivers. 1. Insert t

Strany 40 - Save & Exit Settings

45 3. Select Express and click Next to proceed with the installation. On the following screen, click Finish to complete the installation process.

Strany 42 - Driver Installation

47 Realtek High Definition Audio Driver Installation Follow the steps below to install the Realtek HD audio drivers. 1. Insert the CD that comes wi

Strany 43

48 2. When the welcome screen to the Audio Driver Setup appears, click Next to start the software installation. Once the InstallShield Wizard is com

Strany 44

49 Realtek LAN Controller Drivers Installation Follow the steps below to install the Realtek LAN drivers. 1. Insert the CD that comes with the syst

Strany 45

5 Safety Information Your SI-18 is designed and tested to meet the latest standards of safety for information technology equipment. However, to ens

Strany 46

50 3. When the Welcome screen of the InstallShield Wizard appears, click Next to continue. 4. When the InstallShieldWizard has finished installin

Strany 48

6 Care during use  Do not walk on the power cord or allow anything to rest on it.  Do not spill water or any other liquids on your system. 

Strany 49

7 Acknowledgments  AMI is a registered trademark of AMI Software International, Inc.  AMD and ATI are registered trademarks of AMD Corporation.

Strany 50

8 Accessories a. Power Cord x 1 b. Driver CD x 1 c. Power Brick x 1

Strany 51

9 Components I/O View Refer to the diagram below to identify the components on this side of the system. DVI The Digital Visual Interface (DVI) port

Příbuzné modely SI-08

Komentáře k této Příručce

Žádné komentáře